- Contact：Mr. Song
- Phone：0086-13705113637
- Tell：0086-0515-88809180
- Fax：0086-0515-88809181
- E-mail：jsjckt@126.com
- Address：No. 18, Rongguang Road, National High-tech Park, Yancheng City, Jiangsu Province
Air conditioning automatic control introduction: JCZK-type combined air processing unit control system uses a highly reliable intelligent industrial grade microcomputer for international advanced air conditioners to control the full isolation type of various unit devices, multi-point input computer Devices, hardware and software are modular design, flexible configuration, good extension, software advanced, can always operate in a good state, while achieving energy saving and control accuracy requirements, direct digital controller in this DDC can be Single alone automatically runs, but also through the network controller and the central management unit into a distribution test system.
Industrial air conditioner -JCZK type combined air treatment unit - air conditioning automatic control engineering principle: In the air processing unit control system, the temperature, humidity is controlled, and the wind tube sensor monitors the temperature and humidity of the air, and the instrument is based on the PI operation. As a result, the electrical regulating valve is proportionally, centralized control, adjustment cooling, hot water, and steam amount, the air humidity is maintained within the desired range.
Industrial air conditioning - JCZK type combined air treatment unit ---
1, mixed section
The top of the mixing section is provided on the top of the side block, usually the top air outlet is used for returning wind, and the surface of the side block is a new venting inlet. The new air in the plug can also be used according to engineering or cancellation, or can meet the use of new wind conditions.
2, early, sub-high-efficiency filter section
The non-woven bag filter is provided, the disassembly is convenient, and the frame is sealed. The initial filter filter is a WY-CP-9 non-woven fabric. The mid-range filter material is WZ-CP-2 non-woven fabric. The mid-range filter section is necessary to purify the air conditioning system and should be devices after the blowing machine segment (s). Rent, ginnometric filter segments set differential test instruments, differential differences on site.
3, muffin section
A modular block combination muffler is provided in the segment, with a noise of 15-20 dB (a).
4, new wind, return wind, exhaust adjustment section
The top of this paragraph is a new wind, exhaust, and the adjustment valve is set, and one is set back to the wind adjustment valve. Double fans system and venting, set this paragraph to the return exit to flexibly allocate three parts of the air volume.
5, second return
The top of the secondary return air section sets a secondary return air conditioning valve.
6, the intermediate section
The segments are connected to the internal maintenance, and the door is opened, and the distance is 250mm.
7, send, return air segment
Efficient energy-saving double-in-wind turbine is equipped with high-efficiency and energy-saving duplex, and the spring damping pedestal is equipped with a spring damping pedestal. It has a good vibration. It has a smooth operation and low noise.
Industrial Air Conditioning - Introduction of JCZK Combined Air Conditioning Units
The blowing machine segment is divided into three types (s), vertical (h) and the lower exit (D) in accordance with the wind turbine. The top of the air-conditioning segment can be opened secondary back to shorten the length of the air conditioner. The top of the return airline can be opened once, the new air, the new exhaust, and the designs need to be selected. The air conditioner of the company is equipped with a fan type. The fan export soft joint is in the chassis. The export regulating valve should be configured outside the chassis. It is selected by the engineering design. Our company can order in accordance with the project design; the bottom of the chassis is dimensioned The fan exit size is consistent. The electric motor of the back fan and the blower is equipped with an external type, and the wind turbine has a reliable shaft elastic seal. The external electric motor is separated, and the fan in the chassis is shocked.
8, all flow
After the segment is placed in the water segment and the blower segment (s), there is a reduced air engine outlet dynamic pressure, uniform gas flow, and ensure the use of the filter. Replace the past cutting plate before the water segment.
9, heating section
The heater has two types of copper tube (D / 4) set of aluminum sheets and steel pipes. The number of exclusions of the heaters have a row, two rows and three rows, optional. Hot water and steam can be used as a single circuit structure when the steam heat medium is used.
10, table cold retaining water board
When the cleansing wind speed Vy is 2.5m / s, this paragraph consists of a refrigerator and a water retaining plate, the chiller is a copper tube double-flabed aluminum rib or a copper rib structure, manufacturing excellent, cooling rate Bureau. The number of tandems has four, six, eight, ten rows, and the performance form is based on the 3.0mm specification. The water retaining plate is a glass steel molded water milling effect, and the water retaining plate is convenient in the section. If the wind speed VY <2.5m / s is opened by the surface of the finish, there is no water retaining plate. At the bottom of this paragraph, a drip tank is provided, and there is a drain pipe on the side of the drip tank.
11, 淋 水 表 冷
Composed of the seller and the single row water chamber. Improve the heat transfer coefficient of the refrigerator and purify the air.
12, sprinkle section
There are three rows of second rows, three rows and double-level four rows. There is a tandem and a water retaining plate in the segment, the nozzle is fl shape, the spray hole is 4.0mm, and the water spray pressure is 0.15 MPa, each water sprinkle is 250 kg / h, high efficiency energy saving.
13, dry steam humidifier
This sector is configured with a dry steam humidifier, three types of manual (MSH) pneumatic (QSH) and electric (ESH) for engineering design.
14, send the wind section
This section is located in the top (vertical outlet), three sides (horizontal wind) and the bottom plate for engineering options. The dry steam humidifier can also be set in this paragraph to shorten the length of the air conditioner. This paragraph only needs to be placed when there is still other functional segments after the blower segment; it is generally not placed.
15, turn section
This paragraph has two types of horizontal corner and vertical turning section. When the equipment room is not enough, the horizontal turning section can be selected, and the guiding plate is contained in the segment, and the air is delivered is uniform. When the room is high, the space can be used, and the vertical turn section can be used, which is installed on the blower segment (h), and then then the selected function segment, such as: muzzle segment, humidification section, - second heating section, Incidentally, a mid-range filter segment, a feed section, etc., form a stacked air conditioning unit. ,
16, motor, lighting and instrument test holes
The air conditioner has a 36V40W waterproof lighting in the mixed section, an intermediate section, a dry steam wet section, a secondary return? Air conditioner power control cabinet provides air conditioners with all power equipment power supply operations, interlocks guarantee and display alarm system, and provide a 36V safety voltage lighting system. The user is responsible for the 380V power line to connect to the control cabinet and connected to each power device.
